close

Front panel

Product priceConsultation required
Product information차량 전방에 부착되어 디자인 효과 증대 및 충돌 시 충격흡수를 하기 위한 부품
TAG#Xient #largetruck #Hyundai Automobile #Hyundai truck #Hyundai Commercial vehicle
#Front Panel #metalic paint #clear paint
Product packaging and Shipping conditionsPackaging & Shipping
50kgs/Pallet, Carton Box

Contact Supplier

Contacts

백두진
010-3684-8412
onlybback@idongsung.com

Contact supplier

Related Products

Spoiler-3-1

Spoiler / Roof cover

차량 상단부에 부착되며 디자인 효과 증대 및 고속주행 시 연비절감기능을 하는 부품
Engine-Cover

Engine Cover

엔진 內 외부이물질 유입을 방지하고, 엔진내부에서 발생하는 열을 차단하는 기능을 하는 부품
Gab-Bar-2

Grab bar

버스 승하차 시 안전 및 편의제공를 위한 부품
75_2

Crashpad

차량 내부 운전석 전면유리 하단에 부착, 계기판 및 공조장치 등이 조립되며 충돌 시 탑승자의 충격완화 뿐만 아니라 차 내부분위기를 결정짓는 부품

적용차종

HMC : UNIVERSE

KMC : GRANBIRD

HMC : ELECTCITY

HMC : XCIENT

HMC : UNICITY

Product Description

SMC material

  • excellent thermal vulcanizing ability, excellent strength, and electrical insulation characteristics.
  • SMC is a press molding material on a sheet with excellent moldability by impregnating unsaturated polyester resin with reinforcing material, filler, mold release agent, pigment, catalyst etc. and increasing viscosity by chemical to increase viscosity. Thus, SMC can be adjusted according to the desired physical properties of the product because its change range of strength and various physical properties is wide according to the impregnation and arrangement of glass, which is a reinforcing material, and the filler.

< Reliability Test >

Test item Test method Unit Category Test result Requirements
Gloss MS 655-08 : 5th – 1 88.4 –
Water resistance MS 655-08 : 5th – 1 Exterior No color change, discoloration, swelling, cracks, exposure of substrate etc. No discoloration, change of color, cracking, gloss degradation, on the coating film, andAdhesive is M-1, 0 ~

Within M~2.5 Color difference(△E*) : 2.0 or less /

Gray scale(Grade) : Grade 3 or more
Adhesive(Grade) M-1.0
Color difference

(△E*)

 0.47
Gray scale(Grade) 4-5
Scratch resistance MS 655-08 : 5th Grade 1 4 3.5 or more
Moisture resistance MS 655-08 : 5th – 1 Exterior No color change, discoloration, swelling, cracks, exposure of substrate etc. No discoloration, change of color, cracking, gloss degradation, on the coating film, andAdhesive is M-1, 0 ~

Within M~2.5 / Color difference(△E*) : 2.0 or less /

Gray scale(Grade) : Grade 3 or more
Adhesive(Grade) M-1.0
Color difference

(△E*)

 0.42
Gray scale(Grade) No discoloration, change of color, cracking, gloss degradation, on the coating film There should be no discoloration, change of color, cracking, gloss degradation, and substrate exposure on the coating film /

Gray scale(Grade) : Grade 3 or more
Gray scale(Grade) 4-5
Salt Spray Resistance MS 655-08 : 5th – 1 Exterior No color change, discoloration, swelling, cracks, exposure of substrate etc. No discoloration, change of color, cracking, gloss degradation, on the coating film, andAdhesive is M-1, 0 ~

Within M~2.5 / Color difference(△E*) : 2.0 or less /

Gray scale(Grade) : Grade 3 or more
Adhesive(Grade) M-1.0
Color difference

(△E*)

 0.29
Gray scale(Grade) 4-5
PencilHardness MS 655-08 : 5th – 1 H or more HB or more

< Material report >

Test item Unit SampleCategory Results Test method
Loss ignition % – 29.6 ASTM D2584-11
Specific Gravity

((23/23)℃)

 – – 1.88 ASTM D792-13(A법)
Tensile strength MPa – 111 ASTM D638-14(*)
Flexural strength MPa – 208 ASTM D790-17(**)
Flexural modulus of elasticity GPa – 10.5 ASTM D790-17(**)
Izod Impact Strength J/m – 1.203(P) ASTM D256-10e1(A Method)
Izod Impact Strength

(~40℃)

 J/m – 1.484(P) ASTM D256-10e1(A Method)(***)
Load deformation temperature

(1.82MPa)

 ℃ – Not measurable

(****)

 ASTM D648-16(B Method)
Absorption rate

(24h Immersion)

 % – 0.47 ASTM D570-98(2010)e1

* Test speed : 5 mm/min, Test surface : Type I / ** Test speed : 1.4 mm/min, Distance Between Supports : 50 mm / *** Status control : (-40 ±2) ℃ X 30 min / **** Specified deformation (0.25 mm) does not occur up to maximum temperature of equipment (300 ° C)

Supply Ability

  • Process: 800T/ 1000T/ 2500T PRESS -> Sanding -> Painting -> Assembly
  • Lead Time : 3 days

Packing & Delivery

  • Packaging Details : 50kgs
Rear Bumper Rear-Bumper Garnish Garnish